![]() ![]() 4 - Spread legs out as far as possible for easier access to the center column. 3 – Loosen set screw (#1319) above crank handle (2/23-047-2), and remove crank handle. 2 – Remove lock rings and friction ring (#4027) from bottom of center column, and friction ring (#4027) from above the guide pipe. To purchase parts for this or any SLIK tripod please contact customer service at ****** Written Instructions: 1 – Loosen lock collar (#3879) and bottom lock rings (#’s 14), completely. SLIK USA Customer Service Specialist, Glenn Nash, guides you through the process of replacing the crank handle on a U212 / U212 Deluxe (Universal 212) tripod. And the final bottom lock ring, which screws on to the upper bottom lock ring. The next step is the white friction ring, which goes into the bottom lock ring. Once the crank handle is tightened, you take the first bottom lock ring and screw it on to the bottom of the center guide pipe. It is important not to tighten the set screw too tightly, you will break the bearing on the crank handle. ![]() Reinsert the center column and the head aligning the center guide key with this groove in the back of the center column. Replace the center guide pipe into what I consider the "shoulders" of the tripod. The next step is to reinsert the center guide key into the center guide pipe, just like that. Your have your replacement center guide pipe, the center guide key, two bottom lock rings, a friction rain and your complete crank handle. Now that we have disassembled the center column, these are the parts that you should be left with. Inside the center guide pipe is the center guide key. Once the crank handle is removed, loosen and remove the bottom lock rings, and the friction ring And remove the center column. On the older generations it's a flathead screwdriver. On the newer generation use the 1.5 millimeter hex wrench. Step One: Loosen and remove the crank handle. The parts that you will need: most definitely is part number 1432, the center guide pipe, and possibly 1433, the center guide key. millimeter hex wrench for the newer generation of the 212 Deluxe, or a flatheaded screwdriver on the older generation. Hi, my name is Glenn Nash and today I'm going to show you how to repair the center guide pipe on a Universal 212 Deluxe Tripod. TOOLS REQUIRED: Small flat head screwdriver 10 – Enjoy the use of your rebuilt tripod. 9 – Fit the friction ring (#4027) into bottom lock ring A (#1434) and screw bottom lock ring B (#1455) onto bottom lock ring A. 8 – Re-attach lock collar (#3879) and friction ring (#4027) to top of center guide pipe, and then re-thread bottom lock ring A (#1434) onto bottom of center guide pipe. YOU CAN AND WILL BREAK THE BEARINGS ON THE CRANK HANDLE. 7 – Re-insert crank handle (#2/23-047-2) into tripod and tighten set screw (#1319). Make sure the center guide key sits into the groove on the center column. When replacing, remember to insert the center guide key (#1433) into the groove inside the center guide pipe. ![]() This will enable the center guide pipe (#1432) to be removed, and replaced. 5 – Remove center column (#1918-02) from tripod. We offer Carbon Fiber and Aluminum tripods to fit every need and price point.SLIK USA Customer Service Specialist, Glenn Nash, guides you through the process of replacing the crank handle on a U212 / U212 Deluxe (Universal 212) tripod. Based in Japan, Slik is one of the largest tripod manufacturers in the world. Manufacturing professional and amateur tripods and heads for over 75 years.To purchase parts for this or any SLIK tripod please. SLIK USA Customer Service Specialist, Glenn Nash, guides you through the process of replacing the leg lock on a U212 (Universal 212) tripod. ![]() More Info & Customer Reviews wrp asin=”B00009R6Q8̸.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |